Reloading
 

Reloading discussion moved from another thread.

Thanks R.B.

I'm going to start hand-loading my .270's in the near future. Anyone have any thoughts on reloading?

Doc

hmmm...what kind of press are you getting...?

I have never hand-loaded before and open to suggestions in all aspects of this endeavor.

Thanks,

Doc

depends...if all i were going to load was ammunition for a bolt-action rifle, where accuracy was Job #1, i would get an RCBS Rock Chucker or something like that...you load one round at a time, one component at a time...it is slow, but you are handcrafting each round...if you plan on doing a good deal of shooting in the semi-automatic mode, with either rifle or pistol, i'd recommend a Dillon progressive press...i have an RL 500 from around 1987 that i need to send back for reconditioning that works well...you can reload individual rounds in the same fashion as an RCBS, but you can also crank out a boxload of pistol or 5.56 rounds, as well...

my $0.02

Doc - I would look at getting one of the RCBS Rock chucker kits first. A lot of guys have started hand loading and have found it to be too tedious for their tastes. They soon lose interest and are out a bunch of money if they go high end right off the bat. The nice thing about the rock chucker is that it is versatile and can become your back up your progressive breaks down or needs to go in for anything. It also gets you started and allows you to have the basics that will be needed regardless of the press you wind up using. If you are only going to load for accuracy then that is all you need.

Be careful though, this can become a very addictive hobby with thousands of dollars spent for that last little .001 moa of accuracy. :D

Concur with the Rockchucker.

I started loading for IPSC with one, eventually retiring it for match loading only, using a Dillon 550 for mass production.

If I were only going to do match or hunting loads, I would still get the Rockchucker. If I were running 1000 rounds at the time, I would go with the 550 or 650 from Dillon.

HTH.

TR

Doc - LR1947 is right on the money. If you're going to reload go to Midway or one of the other discounters and buy the RCBS Master Kit. It'll get you started for a reasonable price and everything needed (for entry level reloading) is conveniently bundled. It'll get you started and let you learn. If it works out and you realize enough benefits to get hooked on it then you can start doing the process analysis and throwing money at the problem. Every little incremental improvement after that will cost more - sometimes lots more, either time or money and they're both valuable. FWIW - I've still got (and use) the same Rockchucker I bought in 1981. My Dillon is 14 y/o and going strong. And I'm still spending money to "improve" the process. It's a never ending battle. HTH - Peregrino

P.S. - You will need that quality scope (and excellent record keeping) to realize the full potential of your reloading efforts.

Edited to add: I followed a similar route to TR's though I've actually gone to loading even match rifle ammo on the Dillon. The only rounds I "tweak" are the ones I use at 600m for competition. (I'm not a benchrest shooter - the Dillon gives me one round of moa(-) ammo every time I pull the handle which is all I need at the shorter ranges.)

Doc,

I think I have an old rock crusher in a box downstairs.. I`ll look and see whats there. I`ll let ya know what I find.

Also known as thumb crusher when not paying attention. :eek:

I would like to add my thoughts. Some thoughts would be depending on what you want to load for and how many rounds you plane to load for would help in press choice. The Reaper brought mentioned that. I have a Orange crusher (Lyman, had rock crushers) and two 550B's.

Obviously for massive reloading, Dillion, IMHO, is the only way to go. If your doing small loads amounts, say 50 for pistol, RCBS basic kit. Also for target rifle, Neck sizing is all that is needed if the brass will be used in the same rifle, full length sizing will over stress the brass faster. Again the RCBS is a good way to go. I use a RCBS primer seater for precision loads, slower but a better feel.

Problem with Dillion, it is hard to go back to a single stage press after using one. It is a very versatile press though, more expensive. It does a decent job even for more accurate loads too.

But Boys being Boys given time, if you get into reloading, there will come a time where you will need more space for reloading equipment and shortage of equipment won't be a issue. I load for 36 different cartridges, 5 shotgun gauges, and have to form a few cases that are no longer available. I mentioned to a friend, Reloading is to shooting as foreplay is to sex. I have been reloading for over 30 years, and I still have could add to my reloading equipment. Neat stuff out there.

I was raised as a kid with an RCBS Rockchucker on the work bench so its pretty much all I know. But Dillon has them beats hand down with their calendars and posters! :D
Attachment 5140

i agee with TR regarding match loads...while i got decent results with the Dillon, i got much better results loading one round at a time, using a powder trickler to get my powder weights rights...i'd say the Dillon was within 1-5% in terms of powder weight, while i could get right to the gnat's back using a powder scale...once again, my $0.02...

Funny that the guy that takes these pictures for Dillion is supposed to be a "former" 5th Gp SF soldier. Everytime I've gone to Dillion (even with another former 5th Gp Vietnam Vet) this guy always seems to be "gone".

Everytime time I've gone, I've asked to meet him, everytime time I was told "he's here, let me go get him" and when I tell them I'm also a former 5th Gp Soldier he is always "out to lunch".

Funny....

Anyone know if he's really a 5th Gp Vietnam vet?

Sorry Doc for the Hi-jack....

TS

Thanks for the replies. I'll start out as suggested and see how it goes. I don't shoot the .270 a lot. Maybe 20-40 rounds a month at the nearby range. I have always wanted to reload, so now is as good a time as any to start.

Scotty,

Go ahead with the optics plan if you will. I will wait and see what you come up with on the re-loader too. Thanks a bunch for your help.

Doc