Old 09-30-2011, 09:10   #1
MVP
Quiet Professional
 
MVP's Avatar
 
Join Date: May 2009
Location: AZ
Posts: 618
polishing rifle brass

Searched the site and found nothing...

Does anyone have a recommendation for media to use for tumbling 223 brass? I currently use two sizes; one for 45 caliber plus and one for 30 caliber and up. The smaller stuff used for 30 cal is still too large and will jam in the 223 brass.

MVP
MVP is offline   Reply With Quote
Old 09-30-2011, 15:15   #2
koz
Quiet Professional
 
koz's Avatar
 
Join Date: Feb 2007
Location: TN
Posts: 933
Take a look at the stainless steel media and the Thumbler's tumbler. You'll get a couple pieces stuck in the primer pocket (if you tumble after you deprime) but it will make old brass look very new. I'll give you more details if you like.
koz is offline   Reply With Quote
Old 09-30-2011, 15:19   #3
MVP
Quiet Professional
 
MVP's Avatar
 
Join Date: May 2009
Location: AZ
Posts: 618
media

SS?

Yes please!

MVP
MVP is offline   Reply With Quote
Old 09-30-2011, 18:19   #4
Peregrino
Quiet Professional
 
Peregrino's Avatar
 
Join Date: Jun 2004
Location: Occupied Pineland
Posts: 4,701
I've been using the SS method for three months. It's more involved than the usual methods but the results are well worth the extra effort. (Ask TR.) I just finished 1000 30.06 that look better than new. Everything is well explained on Sniper's Hide. I got the tumbler from the Hobby Lobby (cheapest per Google) and the media from the guy who popularized the method. The original source prefers to maintain his privacy so I'm sharing the contact info with all the usual caveats. Be nice to him, he passed the bona fides tests I used.


From:
Subject: Media supplier

This is from Terry on the Hide........

Contact name is Mark

His email is ac4ht@aol.com

Provide him your contact info Phone, email, best time to contact you!

Marks information is "Confidential and is not to be republished in any form without his direct approval"

Terry
__________________
A nation can survive its fools, and even the ambitious. But it cannot survive treason from within. An enemy at the gates is less formidable, for he is known and carries his banner openly. But the traitor moves amongst those within the gate freely, his sly whispers rustling through all the alleys, heard in the very halls of government itself. For the traitor appears not a traitor; he speaks in accents familiar to his victims, and he wears their face and their arguments, he appeals to the baseness that lies deep in the hearts of all men. He rots the soul of a nation, he works secretly and unknown in the night to undermine the pillars of the city, he infects the body politic so that it can no longer resist. A murderer is less to fear.

~ Marcus Tullius Cicero (42B.C)
Peregrino is offline   Reply With Quote
Old 09-30-2011, 19:39   #5
koz
Quiet Professional
 
koz's Avatar
 
Join Date: Feb 2007
Location: TN
Posts: 933
LINK

Here's a 41pg thread from SniperHide on Stainless Steel Media. Suasponte (Terry) is very helpful if you have questions. I swiped the photos from that thread.

My recipe is Thumblers Tumbler Model B. I got mine from Cabelas. It's a faster tumbler than some others. They sell it for around $180.

I ordered my stainless media from Mark (per Peregrino's post).

I use a shot of Dawn dish detergent and a 9mm case full of LemiShine (you can find it at Target or Walmart in the dish detergent section).

Fill about half full of brass maybe a little more then usually around a gallon of water. It should be near the top. Media is already in the tumbler. Put the top on and let it run for about 3 hrs.

I got a Frankfort Arsenal media separator. I fill that bucket with water (which keep the media from flinging out when you spin the thing. Also get a good magnet (I pulled one out of an old hard drive) so you can pick up any media that falls on the floor.

I dry it under a work light in my garage and it looks like it's brand new. Even brass that sat in the weather for years looks good.

Like Peregrino's post, it takes a little longer but it does wonders to brass. Plus the media never wears out.
Attached Images
File Type: jpg DSCI0001-8.jpg (52.4 KB, 89 views)
File Type: jpg DSC04967.jpg (61.8 KB, 83 views)
File Type: jpg DSC04969.jpg (71.7 KB, 88 views)
koz is offline   Reply With Quote
Old 10-09-2011, 08:32   #6
mark46th
Quiet Professional
 
mark46th's Avatar
 
Join Date: Sep 2007
Location: Orange, Ca.
Posts: 4,941
Sorry this is a little late. Take a look at an ultra sonic brass polisher. They are about $70.00 at Harbor Freight Salvage, up to $200.00 everywhere else. Use 50% distilled water, 50% white vinegar and a couple of drops of dish soap. Run for about 5 minutes.

This cleans out the carbon build-up on the inside of the case which results in more consistent pressures. This isn't important to the average shooter but if you are shooting competitive long range, it is important.
mark46th is offline   Reply With Quote
Reply


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is Off
HTML code is Off

Forum Jump



All times are GMT -6. The time now is 04:31.



Copyright 2004-2022 by Professional Soldiers ®
Site Designed, Maintained, & Hosted by Hilliker Technologies